SUMMARY: RSC configuration problem

Hello All,

I got this from SUN:

Hi

The two topmost reasons for the ethernet port on the RSC card not
working are:

1. tpe_link_test setting

rscadm set tpe_link_test true/false
rscadm resetrsc after making changes

2. Switch port setting on the router.

Try using 10M half duplex in the router.

Thank you,

Paul Quattrociocchi
Sun Support Services



I finally got it right.

Its basically a network issue.  I got my network guru to set the port on
the router to 10, Half Duplex.

Thanks to all those who replied:

ashish.achuthan@wipro.com
Hudes, Dana [hudesd@hra.nyc.gov]
Paveza, Gary [gary.paveza@AIG.COM]

All my settings and config was fine.  Just the network

Abhimanyu Pandey
Information Technologies
Worcester State College
508-929-8913









ORIGINAL POST:


From: Pandey, Abhimanyu
Sent: Tuesday, June 06, 2006 11:54 AM
To: 'sunmanagers@sunmanagers.org'
Subject: RSC configuration problem

Hello All,

I went thru the entire RSC admin manual.   Installed and tested RSC
with:
------------------------------------------------------------------------
------------------------------------------------------------------------
------------------------------


# ./rscadm shownetwork
IP Address: 10.13.50.2
Gateway address: 10.13.1.1
Netmask: 255.255.0.0
Ethernet address: 00:03:ba:cd:37:9d
------------------------------------------------------------------------
------------------------------------------------------------------------
------------------------------



# ./rscadm status

RSC Version v2.2.3
RSC Bootmon Version:  v2.2.2
RSC Bootmon checksum: 10F5D0CC

RSC Firmware Version:  v2.2.3
RSC Build Release: 01

RSC firmware checksum: 6D1CAD09

RSC firmware built: Jan 18 2005, 16:35:07

RSC System Memory Size 8 MB

RSC NVRAM Version = 4

RSC hardware type: 4


------------------------------------------------------------------------
------------------------------------------------------------------------
------------------------------


# ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu
8232 index 1
        inet 127.0.0.1 netmask ff000000
eri0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index
2
        inet 10.13.50.1 netmask ffff0000 broadcast 10.13.255.255
        ether 0:3:ba:b0:37:af
#

------------------------------------------------------------------------
------------------------------------------------------------------------
------------------------------





# ./rscadm version

RSC Version v2.2.3
RSC Bootmon Version:  v2.2.2
RSC Firmware Version:  v2.2.3

------------------------------------------------------------------------
------------------------------------------------------------------------
------------------------------


I have done:
ok diag-console rsc
ok setenv input-device rsc-console
ok setenv output-device rsc-console

------------------------------------------------------------------------
------------------------------------------------------------------------
------------------------------

So everything seems to be fine except that connecting to the server with
RSC client just does not work.


------------------------------------------------------------------------
------------------------------------------------------------------------
-----------------------------------
Ping 10.13.50.2 times out (10.13.50.2 is the RSC, 10.13.50.1 is the
server)





------------------------------------------------------------------------
------------------------------------------------------------------------
-----------------------------------------
Platform: V890, Solaris 10 3/05






Thanks in advance.  This is still a test server so not time critical,
but any insights are very appreciated.

Regards,

Abhimanyu.







"Everything that has been created is subject to decay and death.":
Buddha
_______________________________________________
sunmanagers mailing list
sunmanagers@sunmanagers.org
http://www.sunmanagers.org/mailman/listinfo/sunmanagers